What're your thoughts concerning Installing A Bathtub?
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is also a moderately challenging job. If the old tub is easily easily accessible, the job can relocate easily; if you need to open up a wall surface to eliminate the old bathtub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the work and also fit attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This write-up will certainly help you install a brand-new tub in your restroom if you have actually currently purchased a new bathtub and also don't require to alter the plan of your previous supply of water pipes.
Your devices as well as material list must make up the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in position with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The previous kind should be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Making use of the two wood boards under its feet, position the tub in the called for position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To install taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the water supply and check all joints and new pipework for leaks as well as tighten them if required. Fill up the tub and also inspect the overflow outlet as well as the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bath tub needs to wait till the tub has actually been utilized a minimum of once as this will settle it right into its last placement.
Planning for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Tiling Around the Tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to pass through the wall in between the bathroom and also the tiling, bring about issues with dampness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components as well as fittings. They are offered in tubes and also cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always load the tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our section about Installing A Bathtub. Thanks so much for taking the time to browse our blog. Are you aware of another individual who is curious about the topic? Please feel free to share it. Thanks for your time. Come back soon.
Book Inspection